Blog
Bearings

Bearing materials. How to choose the appropriate one?

by Kevin Sweeney
25 November, 2022
4 min read

Steel as the main material for the manufacture of bearings

Bearing manufacturers have standardized using AISI 52100 steel for manufacturing bearing rings and rolling elements. Rings are heat stabilized to a minimum of +150 C.

Many if not most applications use Chromium steel bearings where the bearing is protected from harsh environmental conditions.

When stainless steel is required or requested all manufacturers offer AISI 440C . Grade 440C stainless steel is a carbon martensitic stainless steel. Having high strength, moderate corrosion resistance, good hardness and wear resistance it is an ideal choice for bearing manufacturing. 

In practice 440C is not a solution for applications in moisture or other corrosive environments.

In saline tests we have conducted 52100 chrome steel rusts at a faster rate than does 440C stainless. Both fail when it comes to rust prevention. In recent years both ceramics and Cronoduir 30 are much more suited for use in hostile environments.

Cronoduir 30 is a stainless martensitic steel having greater corrosion resistance than 440C and is longer wearing:

  • superior corrosion resistance, higher than 1.2083, 1.4112,1.4301, 1.4571
  • high dimensional stability after heat treatment
  • high durability by maximum hardness under static and dynamic demands
  • good wear resistance, higher than 1.4034, 1.2363 or 1.4528
  • tougher and secondary hardening alternative to all corrosion resistant PM-steels
  • high temper resistance up to 500 °C

Cronoduir 30  rings used in conjunction with ceramic balls provide an excellent tribological behavior. Combining Steel and ceramic producing a hybrid bearing improves lubricity and reduces material strain. Low density means the mass is 60% lower than steel and with the centrifugal forces on the rolling elements the kinematics of the bearing are greatly improved.

Bearing rings

Bearing rings undergo fatigue when the bearings are in operation. For rings to support the stresses they must be hardened. AISI 52100 steel contains approximately 1% carbon and 1.5% chromium. Cronoduir in comparison has a significantly finer structure resulting in less heat generated with the permissible contact pressure higher.

Rolling elements

The rolling elements transferring the loads between the inner and outer rings are typically made from the same steel as the rings. So in the case of 52100 standard bearings use 52100 balls and cages and shields. Stainless steel 440C rings would use 440C balls, cages and shields. In the case of Cronoduir 30 to the  contrary it is common for the use of ceramic rolling elements. In the case of super precision bearings used in high speed spindles and other demanding applications the Hybrid model using Cronoduir or 52100 chromium rings along with ceramic balls increases speed and life .

Cages

Cages which separate the rolling elements are typically made from (1) Machined metal, (2) stamped metal, steel pin type and polymer.

Cages vary dependant upon customer and the demands of each application.

For example stamped metal cages are very light weight and are good in high temperatures.

Machined metal cages are manufactured from steel, or brass and are good in high speeds, high temperatures, high accelerations and vibrations.

Polymer cages are usually PA66 or PA46 but other material variations are also used by different manufacturers. Polymer cages are almost frictionless and are consequently used in high speed applications. The use of polymer cages is beneficial in poor lubrication environments as they can continue operating as the material is self lubricating

There are several cage materials and designs. When selecting you will consider the application’s requirements and finding a suitable design is paramount to success. 

Here are some examples of various materials and  standard designs . There are many others including the two piece ribbon and one piece crown type.

Examples of various bearing materials

Shields 

Shields are usually made from strip stainless or chromium steel. Rubber seals usually are manufactured from Buna N Nitrile rubber bonded to a steel shield. Teflon seals are another option from many manufacturers.

Still have questions? Contact us.

Found this useful? Share with:

Written by

Kevin Sweeney

Founder and CEO Pacific International Bearing Sales Inc (PIB)
Education: BS Business and Economics California State University Hayward Ca CBS (Certified Bearing Specialist)
My role with PIB is currently CEO having worked in the bearing industry beginning in 1976. Worked in manufacturing Sales with NTN bearing and Bearing Distribution before creating PIB in 1990. The last 46 years in bearings have been both rewarding and challenging helping so many customers in a broad spectrum of applications. My interests outside of bearings are family , woodworking, motorcycling, cars, gardening , and golf.
Clear All